86-371-67858720
No. 8 Hongye Road, High-Tech Development Zone, Zhengzhou, Henan, China
Hot Sale Solid Waste Dryer Machine Rotary Drum Type Single Pass And Two Pass Heating
1. Brief introduction of solid waste dryer machine :
solid waste dryer machine-Rotary dryer is widely used for drying slag limestone, coal powder, slag, clay, etc. Dryer can also be used in building materials, metallurgy, chemical and cement industry. Rotary Dryer mainly consists of dryer body, raw material feeding plate, driving and supporting device, seal ring, etc. Dryer can be generally divided into four types, they are: rotary dryer, triple-drum dryer, indirect heat transfer dryer, vertical dryer. Different kind of dryer has its own characters and advantages, the specific choice of a special dryer depends on different elements.
2.solid waste dryer machineWorking Principle:
1. Materials are sent to hopper of rotary dryer by belt conveyor or bucket elevator.
2. Materials enter the barrel installed with slope to horizontal line from the higher side, and hot air enters the barrel from the lower side, and then materials and hot air mix together.
3. Materials go to the lower side by gravity when the barrel is rotating.
4. Lifters on the inner side of barrel lift materials up and down in order to make materials and hot air mix completely, which is designed to improve the producing efficiency of rotary dryer.
Rotary dryer internal structure of the lifting plate type :
In order to increase the material evenly distributed on the cross section of the cross section and the drying medium has good contact, in the cylinder body install lifting plate,. There are several kinds of lifting plate for the rotary dryer:
1. Lifting type Lifting plate: suitable for large lump material or easy to be bond in the wall of the material.
2.Four grid type lifting plate: applicable to large density, not brittle or not easily dispersed material. The lifting plate will divide the inside cylinder into four grid, will form a fan operation room not communicating with each other, the contact area of the material and the hot air is larger than the lifting type,and it can increase the material filling rate and reduce material falling height and reducing the amount of dust loss.
3. cross shape or frame shape plate: suitable for more brittle and easily dispersed small pieces of material, so that the material can be evenly distributed in the entire section of the cylinder.
4. sleeve type lifting plate: for multiple heat transfer (or semi diameter heating) rotary drum dryer.
5. cellular type (fan) plate is suitable for fine particles and easy to cause the powder fly. When material feeding is piled up in the lattice board, when the cylinder rotates, the material is stirred and constantly in contact with hot air, at the same time for the material landing height decreases, reducing the possibility of drying materials taken by hot air.
In various forms of lifting plate above can be distributed throughout the whole rotary dryer cylinder, in order to cause the material to quickly and evenly to the lifting plate,can install screw guide material plate at the feed end of 1~5m, in order to avoid the accumulation of wet material bonding on the cylinder wall. At the same time because of dry material is very easy to be raised and was taken away by the waste gas, and in the discharge end of the 1~2m is not installed any lifting plate.
See the rotary dryer flowsheet to understand the rotary dryer working principle:
3. solid waste dryer machine Technical Parameters:
type(mm) | indiclination(%) | rotation speed(r/min) | input tempreture(ºC) | motor power(kw) | outpur(t/h) | weight(t) | reforance |
| Φ600×6000 | 3-5 | 3-8 | ≤700 | 3 | 0.5-1.5 | 2.9 | |
| Φ800×8000 | 3-5 | 3-8 | ≤700 | 4 | 0.8-2.0 | 3.5 | |
| Φ800×10000 | 3-5 | 3-8 | ≤700 | 4 | 0.8-2.5 | 4.5 | |
| Φ1000×10000 | 3-5 | 3-8 | ≤700 | 5.5 | 1.0-3.5 | 5.6 | |
| Φ1200×10000 | 3-5 | 3-8 | ≤700 | 7.5 | 1.8-5 | 14.5 | |
| Φ1200×12000 | 3-5 | 3-8 | ≤700 | 11 | 2-6 | 14.8 | |
| Φ1500×12000 | 3-5 | 2-6 | ≤800 | 15 | 3.5-9 | 17.8 | |
| Φ1800×12000 | 3-5 | 2-6 | ≤800 | 18 | 5-12 | 25 | |
| Φ2200×12000 | 3-5 | 1.5-6 | ≤800 | 18.5 | 6-15 | 33 | |
| Φ2200×18000 | 3-5 | 1.5-6 | ≤800 | 22 | 10-18 | 53.8 | |
| Φ2200×20000 | 3-5 | 1.5-6 | ≤800 | 30 | 12-20 | 56 | |
| Φ2400×20000 | 3-5 | 1.5-5 | ≤800 | 37 | 18-30 | 60 | |
| Φ2800×15000 | 3-5 | 1.5-5 | ≤800 | 40 | 20-35 | 72.5 | |
| Φ2800×18000 | 3-5 | 1.5-5 | ≤800 | 40 | 25-35 | 75 | |
| Φ3000×20000 | 3-5 | 1.5-5 | ≤800 | 55 | 28-40 | 78 | |
| Φ3000×25000 | 3-5 | 1.5-5 | ≤800 | 75 | 32-45 | 104.9 |
4. solid waste dryer machine Features:
1. Our rotary dryer adopts new Spreading plate device, which has guidance, flow, material functions
2. It can make the material content in the dryer radial cross section to full uniform, material will become thin and all.
3. The state of the heat flow entirely, to achieve the purpose of make full use of the heat.
4. Our dryer choose reasonable operating parameters, coal consumption and power consumption of general baked dry machine more than 10-15%, one machine yields above 10-15%.
5. It has been widely used in the cement and mineral processing enterprise.
5. Our Factory solid waste dryer machine and delivery :
6.HengXing Rotary Dryer Installation Site:
Hengxing equipment can provide turkey service for customers, such as engineering consultation, engineering design, equipment manufacturing, packing & transportation, installation & commissioning personnel training etc.
About Spare Parts
Hengxing equipment will be dedicated to provide our customers with genuine spare parts with high quality. With our technological advice, the life cycle of your machine can be prolonged and sustained significantly with high effectiveness.
About Training
Hengxing equipemnt could offer excellent facilities and comfortable environment and training services to different customers. The training should include product training, safety training, operation training, maintenance know-how, technical know-how training, and regulations training, etc. All of the training is customized to fulfill every customer’s expectations. Training programs can be conducted in our workshop, or at customer’s site.
About Installation and Commissioning
Hengxing equipment are able to guide the overall installation of whole set production line, including crushing production line and cement equipment production line, etc., which will allow you to start the normal operation of equipment immediately. After installation,we will make inspection of the whole machine commissioning and operation condition and provide you testing data report of installation.
Our company has realized the computer informationization of management, production, and the CAD and CAPP of production research and process design. We have 29800 square meters of total factory area. We have established strict quality control system to make sure each manufacture step is perfect.
We have passed some international certifications such as ISO, SGS, GMP,CE etc. You can rest assured aboutour machinery.
With advanced CAD&CAPP technology we have built long coorperate relationships with world customers such as America, Cannada, Poland, India, Russia, Australia, Brazil, South Africa, Mongolia, etc. Our products have been exported to 98 countries.
Workshop processing capacity :
About solid waste dryer machine Installation and Commissioning
we are able to guide the overall installation of whole set rotary dryer production line, including stone crushing production line and ball mill production line,rotary dryer production line, etc., which will allow you to start the normal operation of equipment immediately and successfully.
1.How is the quality of your solid waste dryer machine ?
Our products are manufactured strictly according to national and international standard, and we take a test on every grinder before delivery.
2.Guaranteed:
If product quality is not consistent with the description as we described or the promise before you place order, we promise 100% refund.
3.How about Price?
We are manufacturer of 20 years experiences, and be able to give you the lowest price than market one, and we have a policy that “ for saving time and absolutely honest business attitude,we quote as low as possible for any customer, and discount can be given according to quantity”.
For more solid waste dryer machine price and rotary dryer technology ,please
Contact:
Sara
Mobile phone : (whatsapp number): 0086137 8347 1727
Skype: sarapang6
Wechat: sarapang6
Email : sales006*zzhxmachine.com
Website:www.chinamineline.com
www.superballmill.com
